Interactive Media

Completed! Touija Board!

This project was definitely an exercise in design and engineering.  I had originally created an XY axis motion rig on a frame just to test the electronics:

That worked pretty well. I used an Arduino Uno, an Adafruit motor shield v1, nema 17 motors, motor mounts, some 8mm rods, linear bearings, and timing belts.  I made the platforms out of plexiglass because I had some lying around.  I used the Adafruit Stepper motor library, which also uses the AccelStepper library.

Then it came time to design the table itself. I began with the table top, since I had a good idea of the size I wanted. I figured I could reverse engineer it from there.

Then came the hard part.  Retrofit engineering the XY linear motion rig to fit underneath the table top.  I ended up completely starting over because the first prototype was designed to be sitting on a table or floor and the eventual magnet platform would be mounted to the top carriage pointing upwards.  For the tabletop, I intended to mount the hardware underneath the plank, and the magnet carriage would need to be pointing towards the top of the table, which is still up when it’s right side up, but is down when the table is upside down for install.

Once that was sorted, I just had to make the platform that the magnets would sit on.  I don’t have any pictures of that process, but it was mostly trial and error.  Then it was time to test the planchette movement!

In this video I was moving it with my hand.  I was having code issues.  I eventually worked those out, basing my code off of the MultiStepper example from the Adafruit Stepper Motor library.  I was able to get x and y movement, but I discovered that without a way to zero the planchette — to make sure the system knows where the planchette is — it was impossible to try to plot out where each letter was. I added in two momentary push buttons in line with the carriage and the magnet platform so that I could set a basis for movement.

Once that was done, it was possible to actually start plotting out letters.  I did a test video at this point, because I knew that I’d be replacing the vinyl letters and that to plot out where they were now would be pointless.

 

 

Two cans of spray paint and some new vinyl cuts later…. I had this:

IMG_20141214_163226

Lookin Spiffy!

Then it was a matter of plotting out the letters, and getting it to receive the tweets.  I used this tutorial by Lucidtronix as my jumping off point. I have a processing sketch that pulls the latest tweet of whatever search term I specify from twitter, and sends it over a serial connection to the Arduino, which then passes it to a function that cleans it, and parses out each character, telling the planchette where to move.

Overall I am happy with this build, but I will continue to work on it to make it as I had originally envisioned.  The motor shield I’m using does not leave many pins for other functions, so I’ll be replacing it with the newer motor shield from Adafruit.  This will enable me to add a wireless breakout board that will take the place of the current wired USB serial connection.  Once that is done, I will translate the processing code to a Ruby script that will run on my linux server that is handling many of the other functions for my thesis.  Then I can build the rest of the table and its protective plexiglass vitrine.

Touija Board

I had to completely redesign the X Y Motion mechanism for the tabletop that I had cut.

Once I had figured out how to make the movements work in the new space, I was able to begin putting it together.

Here’s a preview of how it will function, once I get all of the motors in place (just one left!)

I may have to slightly redesign the layout of the letters and words, and I’d like to add a little bit more embellishment.  Once the mechanics are working, I’ll build the legs, remove the vinyl letters, spray the table top gold, wait for it to dry, and then apply new vinyl letters with the design.  Then I’ll paint the entire table black, and remove the vinyl so that the gold shows through.  I may add some more embellishment to make the table look more Eastlake-like, but that’s basically it.

Haunted Phone Guts!!

Going from breadboard prototyping to soldering onto a pcb is always harrowing.  I made this fritzing sketch to help me stay organized and remember what I’m doing.

This setup enables the phone to receive text string messages over serial to the arduino, which then rings the phone and upon pick up, passes the text message to the EMIC text-to-speech card, which then speaks the text.

hauntedPhone

 

Wiring up the EMIC was the easy part, but the bells on this old phone were meant to run off of AC power.  That means that to get the bell to ring with DC Power, I have to alternate the direction of current on my own.  I’m doing this using two sets of NPN and PNP transistors. Using 4 digital pins, I’m turning on and off the transistors in such a way as to provide power and ground through alternating sets of transistors, and feeding that to the bells.  What a pain!

Pin 2 on the arduino is used for the receiver switch.

IMG_20141130_223043

I used an old deprecated arduino protoshield because I had one on hand. I also used Sparkfun’s Swiss Machined Female Headers for the transistors, because when I was breadboard prototyping they burned out a couple of times if the power was applied to the 12v rail before the arduino provided power to the transistors to act as gates. Using these headers makes it easy for me to be able to switch out the transistors if they burn out again, but hopefully they won’t.

I’m waiting on some wireless chips from ebay to get this completely installed into the phone, but other than that, it’s pretty much done(for now).

Eventually I’d like to add a functionality to be able to send 5 seconds of audio from the phone microphone to the website, but that gets into streaming and other more complex issues I’d rather not tackle at the moment.

 

Fun stuff, capacative touch and ultrasonic fog!

11-20-14 fog

Testing out my relay

Testing my relay

Up to awesome thingssssss (partial thesis progress)
URECA 2013

So I’m proud to announce that I have 3 works featured in this year’s URECA Celebration.

My photograph “Into the Woods” and my interactive piece “The House Project” will both be featured in the URECA Art Exhibition; and my current project EmoteControl, which I’m working on with Eric Engoron and Min Sung Jung, will be featured in the Celebration Exhibition as well.

I’m honored that so much of my work is being recognized this year, and I look forward to the event on April 24th at Stony Brook University!

Final projects!!

The end of the semester is here and it’s time to get together all of my final projects. I have a lot of things going on for my different classes. The least interesting is this:

A mask I’m making for my computers and sculpture final.  It’s made by cutting out 32 columns and 29 rows of black and white strips, then weaving and gluing them together.  It is more tedious than anything I’ve had to do for school so far.

For my design class, I’m working on compiling an electronic and print version of a  children’s book that I wrote and my friend Marina Labate is illustrating.

In photo II, I’m constructing a display for an image that will make the construction of the image apparent. No spoilers!

And for my interactive media class, I’m working with my husband to try to interface an Atari controller with a RaspberryPi to use in conjunction with a wireless webcam to create a human video game.  It should be pretty interesting.  There are test videos on my ustream channel here, though I don’t believe I will be using ustream for the actual project.

“Home” Project Critique and Artist Talk

Special thanks to Jeremy Dennis for the video.

No Newer Posts
No Older Posts